CM
CIVILMATRIX LAB
STANDARDIZED TAKEOFF 📐 SPEC: 16' × 24' × 6" ACI 318-19 STRUCTURAL ASTM C94 BATCHING ACI 302.1R JOINTING

Calculadora de Losa de Concreto de 16×24 Pies (4.9m × 7.3m)

Cómputo métrico losa 16x24 (4.9x7.3m, 15cm): requiere 5.98 m³ de concreto con 10% de merma, 503 sacos de cemento 25kg y malla de acero. Normativa ACI 318.

Ready-Mix Order 7.82 yd³ 1 Transit Truck
Bag Alternative 352 Bags 80 lb Pre-Mixed
Steel Rebar Grid 633 LF #4 Bar (32 Sticks @ 20')
4" Stone Sub-Base 7.63 Tons ASTM #57 (1.15x Comp.)
Presets:
← Master Calculator
Slab Thickness / Depth 6 Inches
4" (Standard Patio/Garage) 5" (Light Truck) 6" (Commercial Shop) 8"+ (Heavy Industrial)
Rebar Grid Spacing (ACI 318) 18 " on-center (#4 Grade 60)
12" (Heavy Vehicle/Forklift) 18" (Standard Residential/Shop) 24" (Light Duty Foot Traffic)
ACI 318-19 / ASTM C94 CAD
4,000 PSI Structural Concrete
#4 Rebar Grid (40d Lap Splice)
4" Compacted ASTM #57 Stone Base
SITE PROCUREMENT

Bill of Materials (BOM)

TOTAL READY-MIX CONCRETE ORDER (10% OVERAGE) ASTM C94
7.82 yd³ 1 Truck
RETAIL BAG EQUIVALENT 352 bags (80 lb) or 470 bags (60 lb)
NET SLAB VOLUME 7.11 yd³ 384 sq ft footprint
SPECIFICATIONS & LOGISTICS:
Rebar Grid Linear Length (40d): 633 ft (32 sticks @ 20')
Total Reinforcing Weight: 423 lbs
Compacted Stone Sub-Base (4" #57): 7.63 Tons
Excavation Cut & Haul-Off: 14.81 yd³ (2 Tri-Axle Loads)
Estimated Material Order Cost: ~$1,963
⏱️ ASTM C94 TRANSIT MIX DISCHARGE:

Concrete must be completely discharged within 90 minutes (or 300 drum revolutions) after water addition at the ready-mix batch plant. Prepare pump, forms, and crew prior to truck arrival.

SPECIFICATION SUMMARY MATRIX ACI 318-19 / ASTM C94 / ASTM C387

16' × 24' Concrete Slab Quick-Reference Material & Volume Table

A 16' × 24' concrete slab (384 sq ft) requires between 5.21 cubic yards (at 4" depth) and 7.82 cubic yards (at 6" depth) of ready-mix concrete incorporating an essential 10% safety overage for subgrade variance and formwork deflection. If utilizing pre-mixed bags, plan for 235 to 352 80-lb bags (or 313 to 470 60-lb bags). Grade 60 #4 rebar grid reinforcement requires 32 to 32 twenty-foot sticks tied at 18" on-center spacing with standard 40d tension development lap splices.

Slab Depth Concrete Volume (yd³) 80 lb Bags 60 lb Bags Rebar Grid (#4 Grade 60) Structural Application
4" (10 cm) 5.21 yd³ (4.74 yd³ net + 10%) 235 bags (0.60 cu ft/bag) 313 bags (0.45 cu ft/bag) #4 Grade 60 @ 18" O.C. (32 sticks @ 20', 633 LF, 40d splices) Tension development lap splice: 40 bar diameters (20") per ACI 318 Shed pads, walkways, backyard patios & foot traffic
5" (13 cm) 6.52 yd³ (5.93 yd³ net + 10%) 294 bags (0.60 cu ft/bag) 392 bags (0.45 cu ft/bag) #4 Grade 60 @ 18" O.C. (32 sticks @ 20', 633 LF, 40d splices) Tension development lap splice: 40 bar diameters (20") per ACI 318 Standard residential driveways, light pickup trucks, hot tubs
6" (15 cm) CURRENT SPEC 7.82 yd³ (7.11 yd³ net + 10%) 352 bags (0.60 cu ft/bag) 470 bags (0.45 cu ft/bag) #4 Grade 60 @ 12"–18" O.C. (32 sticks @ 20', 633 LF, 40d splices) Tension development lap splice: 40 bar diameters (20") per ACI 318 Heavy 2-car garages, RV pads, commercial workshops, pole barns
* All volumes include 10% safety overage for subgrade variance and form deflection per ASTM C94 / ACI 318. Dimensions: 16' × 24'
TURNKEY INSTALLATION ESTIMATOR $6.00 to $12.00 / SQ FT INSTALLED RANGE

Turnkey Installation Cost Range Estimator

Dynamic total project cost calculator for a 384 sq ft slab. Covers end-to-end turnkey contractor scope: site excavation, subgrade grading, 4" crushed stone base, vapor retarder, #4 rebar grid, ready-mix concrete, pump truck placement, and professional finishing.

Selected Turnkey Rate $8.50 / sq ft National Residential Avg
Adjust Turnkey Contractor Rate ($/sq ft): $8.50 / sq ft (Standard Residential)
$6.00 / sq ft (DIY / Basic Pour) $8.50 / sq ft (Standard Garage/Patio) $12.00 / sq ft (Commercial / Boom Pump)
TOTAL ESTIMATED PROJECT COST
~$3,264
Full turnkey installation for 384 sq ft footprint
COST BREAKDOWN (ESTIMATED)
Materials (Concrete, Rebar, Stone): ~$1,963
Labor, Grading, Pump & Pour: ~$1,301
$6 TO $12 / SQ FT BENCHMARKS
Low End ($6.00/sq ft): ~$2,304
Average ($8.50/sq ft): ~$3,264
High End ($12.00/sq ft): ~$4,608
ASTM C94 vs ASTM C387 FINANCIAL PROCUREMENT MATRIX

Matriz de Decisión Financiera: Hormigón de Planta vs. Sacos

Comparativa de costes, personal necesario, ventanas de vaciado, fatiga física y análisis de riesgo de junta fría estructural.

🚚
ACI 302.1R LOGISTICS RECOMMENDATION

Veredicto: Pida Camión Hormigonera — el mezclado manual excede el límite seguro de 1 día; alto riesgo de juntas frías.

TRANSIT TRUCK MANDATORY
ASTM C143 / ACI 318-19 SLUMP & HYDRATION VISUALIZER

Visualizador Interactivo de Asiento de Cono (ASTM C143) y Resistencia PSI

Deflexión interactiva del cono de Abrams según ASTM C143, límites de relación agua-cemento (a/c <= 0.45) y curva de curado a 28 días.

1. Select Design Strength Specification (ACI 318-19 Mix Design): 4,000 PSI (27.6 MPa) — Driveways & Garages
2. Select Workability & Slump Deflection (ASTM C143 Cone Test): 4-Inch (100 mm) Slump — Optimal Residential Slab
ASTM C143 ABRAMS CONE DEFLECTION SIMULATION CAD SCALE 1:1 DYNAMIC
12" Abrams Mold Ref.
5/8" Tamping Rod Bar
Slumped Concrete Mass
MIX PROPORTIONING & HYDRATION ACI 318-19 §19.3.2
MAX WATER-CEMENT RATIO (W/C) COMPLIANT (w/c ≤ 0.45)
0.44 w/c ACI 318 Exposure F2

Strict maximum water-cement ratio of 0.45 required by ACI 318 for exterior slabs exposed to moisture and freezing/thawing. Low w/c prevents capillary water absorption and frost scaling.

28-Day Compressive Strength Development ASTM C39 TRAJECTORY
1d
Day 1 (~16%): Form stripping & Saw-cut joints (4–12 hr)
640 PSI
3d
Day 3 (~40%): Pedestrian foot traffic permitted
1,600 PSI
7d
Day 7 (~70%): Passenger vehicles & parking allowed
2,800 PSI
14d
Day 14 (~85%): Light trucks & equipment allowed
3,400 PSI
28d
Day 28 (100%): Design compressive strength verified
4,000 PSI
ACI 308R Moist Curing (7-Day Minimum) ASTM C309 Membrane Approved

Evaluates surface evaporation rate against critical bleed capacity using the official ACI 305R / Menzel Nomograph. When evaporation exceeds 0.20 lb/ft²/hr (1.0 kg/m²/hr), rapid plastic shrinkage cracking is imminent.

Presets:
Ambient Air Temperature (Ta) 68°F
40°F (ACI 306R Cold) 70°F (Optimal) 110°F (Extreme Heat)
Concrete Mix Temperature (Tc) 68°F
50°F (Min Allowed) 65–75°F (Normal Batch) 95°F (Max ASTM C94)
Relative Humidity (r) 55%
10% (Arid Desiccation) 50% (Average) 90% (Saturated Air)
Wind Velocity 20" Above Slab (V) 8 mph
0 mph (Calm) 10 mph (Moderate Breeze) 30 mph (Severe Gale)
ACI 305R EVALUATED NOMOGRAPH FORMULA: MENZEL MODEL
E = [ (Tc)2.5 − r × (Ta)2.5 ] × [ 1 + 0.4 × V ] × 10−6
Thermal vapor gradient Δ: 15,238 Wind factor (1 + 0.4V): 4.20
Evaporation Rate E: 0.0721 lb/ft²/hr (0.352 kg/m²/hr)
SURFACE EVAPORATION DIAL ACI 305R §4.2
0.0 0.10 lb 0.20 lb 0.40+
0.072 lb/ft²/hr
(0.35 kg/m²/hr)
SAFE / LOW RISK
ACI 305R STATUS

Normal Curing Procedures Apply

Evaporation rate is safely below the bleed rate of concrete. Normal finishing operations and standard ASTM C309 membrane curing compound application are adequate.

✂️
CONTRACTION JOINT WINDOW

Early Saw-Cut Joint Timing & Depth Rule

Standard Hydration Window
RECOMMENDED SAWING WINDOW 8 – 14 Hours Post-placement window
MANDATORY DEPTH RULE Minimum D / 4 1.0" for 4" slab / 1.5" for 6" slab
MAX JOINT SPACING 24× to 30× Slab Depth 8'–10' for 4" slab / 12'–15' for 6" slab

Ideal temperature for controlled hydration. Cut contraction joints before final thermal contraction peak to prevent random uncontrolled diagonal slab cracking.

Actionable Jobsite Mitigation Protocol (ACI 305R §4.3) DYNAMIC ACTION REGIMEN
01. MONOMOLECULAR FILM OPTIONAL

Aliphatic Alcohol Retarder

Spray water-based monomolecular evaporation retarder immediately after screeding/bull-floating to form an elastic surface film reducing evaporation by up to 80%.

02. MICRO-DROPLET FOG NOT REQUIRED

Atomized Fog Misting

Deploy high-pressure atomizing fog nozzles upwind to saturate the air (>80% RH) directly over the pour. Never allow fog droplets to puddle on unhardened paste.

03. WINDBREAKS & SHADE MONITOR WIND

Perimeter Barriers

Erect 6-foot solid windbreaks on prevailing windward sides. Every 5 mph wind speed drop cuts evaporation by ~35%. Provide overhead tarps to block direct solar radiation.

04. CURING COMPOUND STANDARD REGIMEN

ASTM C309 Membrane

Apply ASTM C309 Type 1-D or Type 2 Class B white-pigmented curing compound at 200 sq ft/gal immediately after final finishing. In severe heat, follow with 7 days wet burlap.

ADVERTISEMENT
Sponsored Space • Policy Buffer Active
FIELD SPECIFICATION (MEDIUM TIER: 384 SQ FT) ACI 302.1R / ACI 318-19 / ASTM C94 / ASTM D698

Contractor & Field Execution Guidelines

01. ASTM D698

Subgrade & 4" Stone Base

  • • Excavate native subgrade to uniform 10" depth; proof-roll to eliminate soft pockets.
  • • Install 4" ASTM #57 crushed limestone compacted to >=95% Proctor.
  • • Acts as capillary break stopping ground moisture rise & settlement.
02. ASTM E1745

10-Mil Vapor Barrier

  • • Install 10-mil Class A poly directly over compacted stone (no sand layer).
  • • Overlap sheets minimum 6 inches; seal continuously with acrylic vapor tape.
  • • Flash perimeter and penetrations tightly to stop moisture vapor paths.
03. ACI 318 §25.4

Rebar Chairs & 40d Lap

  • • Support Grade 60 steel on CRSI chairs @ 30"–36" OC in upper-middle third.
  • • Maintain 2.0" clear cover above vapor retarder; tie with double-snap wire.
  • • Execute 40db tension lap splices (20" overlap for #4 rebar).
04. ACI 302/308R

Joint Timing & Curing

  • • Saw-cut joints @ 1.5" depth (1/4 T) within 4–12 hr green window.
  • • Space joints at max 24x–30x thickness (typically 8'–10' square bays).
  • • Apply ASTM C309 curing membrane immediately; 48-hr pedestrian lockout.
DIMENSIONAL TAKEOFF SPECIFICATION ACI 318-19 / ASTM C94 Calibrated

16' × 24' Slab Engineering Takeoff

PE / SE CODE-ALIGNED
CALCULATED FIELD BILL OF MATERIALS
16' × 24' × 6"

Cómputo técnico para una losa de 16×24 pies (4.88m × 7.32m) con 6 pulgadas de espesor (15.2 cm). Área total de 384 pies cuadrados (35.67 m²). Requiere un volumen de 5.98 m³ de concreto estructural con 10% de merma, equivalente a 503 sacos de 25kg. Se recomienda subbase granular compactada de 10 cm (7.63 toneladas) bajo normativa ASTM D698 y armado con 32 barras de varilla corrugada.

GROUNDING: ACI 318-19 • ASTM D698 +10% SAFETY OVERAGE
PE
CIVIL & STRUCTURAL REVIEW BOARD CivilMatrix Technical Editorial Team | PE / SE Validated
CODE-ALIGNED
Consensus Code Grounding:

ACI 318-19 §25.4, ASTM C94/C94M, ASTM D698, ASTM C90, IBC 2024.

Editorial Review Standards:

Deterministic mathematical modeling based strictly on published building codes. Zero promotional bias.

LAST TECHNICAL CALIBRATION: November 2026 • v2.4
JOB-SITE DIRECTORY

Job-Site Technical Frequently Asked Questions

ACI 318 • ASTM C94 Standard Solutions
Q ¿Cuánto concreto se necesita para una losa de 16×24 con 6" de espesor?
A

Una losa de 16×24 con 6 pulgadas de espesor requiere 7.82 yd³ (aprox. 5.98 m³) de concreto premezclado con un 10% de desperdicio por desniveles del terreno. Para más de 3 m³, se recomienda entrega directa en camión hormigonera.

Q ¿Cuánto cuesta instalar una losa de concreto de 16×24 llave en mano?
A

Una losa de concreto de 16×24 (384 pies cuadrados) instalada por contratistas tiene un costo promedio de $2,304 a $4,608 ($6 a $12 por pie cuadrado). Incluye excavación, grava subbase, armadura de varilla #4, 7.82 yd³ de concreto y acabado profesional.

Q ¿Cuántos sacos de concreto se necesitan para una losa de 16×24?
A

Se requieren aproximadamente 352 sacos de 80 lb (470 sacos de 60 lb o aprox. 503 sacos de 25 kg) para una losa de 16×24 con 6" de espesor.

Q ¿Cuál es la armadura de acero y solape requerido según ACI 318?
A

Se prescribe malla de varillas corrugadas #4 (12 mm / 1/2") espaciadas a 45 cm (18") en ambas direcciones, con solapes de tracción de 40 diámetros (50 cm) y separadores plásticos de 5 cm de recubrimiento libre.

Q ¿Cuánta grava o subbase granular se requiere bajo la losa?
A

Una subbase de 10 cm (4") de grava triturada ASTM #57 requiere aproximadamente 7.63 toneladas de material compactado al 95% del ensayo Proctor Modificado (ASTM D698).

Q ¿Cuál es el tiempo máximo de descarga del camión hormigonera?
A

Conforme a la norma ASTM C94, el concreto debe colocarse y terminarse dentro de los 90 minutos posteriores al contacto de agua y cemento en planta para evitar fraguado inicial no controlado.